Tutorial Pemrograman dan Pembacaan Tag Input RFID-RC522 Menggunakan Arduino Uno R3

Kali ini saya akan berbagi Tutorial Pemrograman dan Pembacaan Tag Input RFID-RC522 Menggunakan Arduino Uno R3. Jika tag terdeteksi dan dikenali oleh Arduino, maka Arduino akan menampilkan output sesuai kondisi yang didapat pada Serial Monitor Arduino IDE. Anda bisa download dahulu Library Arduino nya di link berikut ini: DOWNLOAD LIBRARY.



1. Arduino Uno R3 >>> BELI DISINI

2. RFID-RC522 >>> BELI DISINI

3. Kabel Jumper >>> BELI DISINI



Berikut ini adalah gambar rangkaiannya :






Koneksi antar PIN seperti berikut ini :






Berikut ini adalah Code Programnya :

/***************************



Tutorial Pemrograman dan Pembacaan Tag Input RFID-RC522 Menggunakan Arduino Uno R3



Oleh: Arduino Indonesia

Website: www.arduinoindonesia.id

Toko Online: www.workshopelectronics3in1.com

Blog: mycoding.id



Copyright @2019



****************************/



#include <AddicoreRFID.h>

#include <SPI.h>



#define  uchar unsigned char

#define uint  unsigned int



uchar fifobytes;

uchar fifoValue;



AddicoreRFID myRFID; // create AddicoreRFID object to control the RFID module



/////////////////////////////////////////////////////////////////////

//set the pins

/////////////////////////////////////////////////////////////////////

const int chipSelectPin = 10;

const int NRSTPD = 5;



//Maximum length of the array

#define MAX_LEN 16



void setup() {               

   Serial.begin(9600);                        // RFID reader SOUT pin connected to Serial RX pin at 9600bps



  // start the SPI library:

  SPI.begin();

 

  pinMode(chipSelectPin,OUTPUT);              // Set digital pin 10 as OUTPUT to connect it to the RFID /ENABLE pin

    digitalWrite(chipSelectPin, LOW);         // Activate the RFID reader

  pinMode(NRSTPD,OUTPUT);                     // Set digital pin 10 , Not Reset and Power-down

    digitalWrite(NRSTPD, HIGH);



  myRFID.AddicoreRFID_Init(); 

}



void loop()

{

    uchar i, tmp, checksum1;

  uchar status;

        uchar str[MAX_LEN];

        uchar RC_size;

        uchar blockAddr;  //Selection operation block address 0 to 63

        String mynum = "";



        str[1] = 0x4400;

  //Find tags, return tag type

  status = myRFID.AddicoreRFID_Request(PICC_REQIDL, str);

  if (status == MI_OK)

  {

          Serial.println("RFID tag detected");

          Serial.print("Tag Type:\t\t");

          uint tagType = str[0] << 8;

          tagType = tagType + str[1];

          switch (tagType) {

            case 0x4400:

              Serial.println("Mifare UltraLight");

              break;

            case 0x400:

              Serial.println("Mifare One (S50)");

              break;

            case 0x200:

              Serial.println("Mifare One (S70)");

              break;

            case 0x800:

              Serial.println("Mifare Pro (X)");

              break;

            case 0x4403:

              Serial.println("Mifare DESFire");

              break;

            default:

              Serial.println("Unknown");

              break;

          }

  }



  //Anti-collision, return tag serial number 4 bytes

  status = myRFID.AddicoreRFID_Anticoll(str);

  if (status == MI_OK)

  {

          checksum1 = str[0] ^ str[1] ^ str[2] ^ str[3];

          Serial.print("The tag's number is:\t");

          Serial.print(str[0]);

            Serial.print(" , ");

          Serial.print(str[1]);

            Serial.print(" , ");

          Serial.print(str[2]);

            Serial.print(" , ");

          Serial.println(str[3]);



          Serial.print("Read Checksum:\t\t");

            Serial.println(str[4]);

          Serial.print("Calculated Checksum:\t");

            Serial.println(checksum1);

           

            // Should really check all pairs, but for now we'll just use the first

            if(str[0] == 197)                      //You can change this to the first byte of your tag by finding the card's ID through the Serial Monitor

            {

                Serial.println("\nHello Craig!\n");

            } else if(str[0] == 244) {             //You can change this to the first byte of your tag by finding the card's ID through the Serial Monitor

                Serial.println("\nHello Erin!\n");

            }

            Serial.println();

            delay(1000);

  }

   

        myRFID.AddicoreRFID_Halt();      //Command tag into hibernation             

}

Upload Code Program di atas ke Board Arduino. Lalu Klik >> Serial Monitor. Lalu dekatkan RFID Card anda di RFID Reader RC522. Nilai Tag dari RFID Card akan terlihat pada tampilan Serial Monitor Tersebut.













Tag :

toko arduino, arduino online,
jasa arduino, toko elektronik, arduino, arduino adalah, arduino
download, arduino ide, arduino projects, toko elektronik malang, toko
elektronik bandung, toko elektronik surabaya, belajar arduino, harga
sensor, jual arduino glodok, arduino serial, arduino tutorial, jual
komponen elektronika grosir dan eceran, arduino pdf, modul arduino,
arduino uno projects, jual komponen elektronika glodok, simulator
arduino, arduino indonesia, arduino programming, arduino servo, arduino
android, proyek arduino untuk pemula, arduino pwm, ldr arduino, toko
robot, ebook arduino, motor dc arduino, software arduino, arduino
eeprom, arduino led, pwm arduino, toko komponen elektronik terlengkap,
arduino timer, program arduino, arduino nano datasheet, arduino uno
schematic, jual komponen elektronika, toko komponen elektronik online
terpercaya, arduino nano pinout, arduino software, tutorial arduino,
harga arduino uno asli, proyek arduino, toko komponen elektronik online,
arduino simulator, arduino code, toko komponen elektronik, lm35
arduino, arduino controller, arduino library, arduino atmega328, toko
electronic, arduino bluetooth, toko elektronik di bali, projek arduino
uno, toko elektronik di surabaya, toko elektronik online, mikrokontroler
arduino, toko elektronik tangerang, toko elektronik di denpasar

Katalog produk arduino, cek dibawah ini.